Is my Chain Set Worn?

Ablang

Is my Chain Set Worn?
By Alastair Hamilton

http://www.bikecyclingreviews.com/f...n_Set_Worn.html

Alan Collett has been having problems with his drive train, he has
bought a new chain and cassette and things are better, but not perfect
as it still skips. He wants to know if this can be fixed by rear gear
adjustments or if he will have to buy a new chain set also? Here is
what we think

Question:
My Campagnolo Veloce 9 speed started skipping when pushing hard. As it
has done several thousand miles I changed the chain and rear cassette.
It now runs noticeably smoother in all respects except that it still
skips. Can this be fixed by adjustments or will I need to replace the
chain set as well.

Hi Alan,

Normally the chain set lasts a lot longer than the chain and cassette
and should last you many years before needing replacing. If it did
then you can replace the chain rings without having to replace
everything, unless you want to up grade, of course.

Worn Chain Ring?

To tell if your chain rings are worn, or more precisely the teeth on
the chain rings, if you can lift the chain off the chain ring teeth at
one point while the chain is still wrapped round the chain ring, then
it is worn, or look at the teeth on the chain ring, are they hooked?
As you look at the tooth from the chain set side, leading face of the
tooth or the right side, doesn't look like the other side, it has a
hook look about it? If so then it is worn. As I said before the chain
rings take a lot longer time to wear than the cassette, due to them
being bigger and having more teeth to wear out.

Rear Mech

The Skipping

First, does it skip on all the gears? If so it's probably a cable
adjustment that is needed. Make sure that the chain is running OK on
the smallest cog on the cassette and doesn't need the adjusting screw
turned to let the rear mech move out or not go as far as it is doing.
If this is good then change from the first sprocket to the second, if
it is not moving up enough then you need to tighten the cable with the
adjuster on the rear mech, if it is going to far then you need to let
the cable out a little. Once you have the perfect change between the
first and the second cog on the cassette then all the others should be
good too, run through all the gears on the big and small chain rings
to make sure they are good and that should be you with perfect gears.

Cable Adjuster

If it is still skipping then it is possibly a stiff link and as this
is a new chain it will probably be the link that was used to join it,
its always a good idea to clean a new chain as it is packed with a
very sticky grease that it used to stop the chains from going rusty
when they are in transit or in storage. Clean the chain with degreaser
or a thin oil and remember to re-oil it afterwards, it will run much
more smoothly. If all this doesn't help drop us another line and you
can let us know how you get on.

Bill Sornson

Ablang wrote:
> Is my Chain Set Worn?
> By Alastair Hamilton
>
> http://www.bikecyclingreviews.com/f...n_Set_Worn.html
{snip}

Jobst once claimed (/stated/) that chain rings do not wear enough to cause
chain skip. Period. Many spoke up immediately in objection, but of course
he never responded nor recanted his original contention.

FWIW, BS

travis.harry@gmail.com

On Jun 2, 11:51 am, "Bill Sornson" <as...@ask.me> wrote:
> Ablang wrote:
> > Is my Chain Set Worn?
> > By Alastair Hamilton
>
> >http://www.bikecyclingreviews.com/f...n_Set_Worn.html
>
> {snip}
>
> Jobst once claimed (/stated/) that chain rings do not wear enough to cause
> chain skip. Period. Many spoke up immediately in objection, but of course
> he never responded nor recanted his original contention.

The first of the criteria in this article is incorrect. I put a new
Sachs or SRAM chain on new chainrings of different manufacturers, and
they all fit under the chain differently, some allowing distinctly
different amounts of lift. I asked on this list how to know,
quantitatively, that a chainring was worn, and was told by such as
Andrew Muzi :It's worn out if the chain skips.

Unanswered was a second question: Does a worn chainring wear out
chains prematurely. Expensive as 10 speed chains are, and plentiful as
chainrings are, this could cause you to care more about worn rings.

Travis
DC USA

A Muzi

>> Ablang wrote:
>>> Is my Chain Set Worn?
>>> By Alastair Hamilton
>>> http://www.bikecyclingreviews.com/f...n_Set_Worn.html
>> {snip}

> "Bill Sornson" <as...@ask.me> wrote:
>> Jobst once claimed (/stated/) that chain rings do not wear enough to cause
>> chain skip. Period. Many spoke up immediately in objection, but of course
>> he never responded nor recanted his original contention.

travis.harry@gmail.com wrote:
> The first of the criteria in this article is incorrect. I put a new
> Sachs or SRAM chain on new chainrings of different manufacturers, and
> they all fit under the chain differently, some allowing distinctly
> different amounts of lift. I asked on this list how to know,
> quantitatively, that a chainring was worn, and was told by such as
> Andrew Muzi :It's worn out if the chain skips.
>
> Unanswered was a second question: Does a worn chainring wear out
> chains prematurely. Expensive as 10 speed chains are, and plentiful as
> chainrings are, this could cause you to care more about worn rings.

I wasn't being flippant; chainring wear is not usually obvious otherwise.

Jobst refers to classic road rings, relatively clean, hard, of good
quality and in sizes over 42t. Today, with 32t and 36t middle rings
driven by never-lubricated chains, the teeth erode down to little stumps
on the lower range of urban bikes. Modern chains wear so fast that
excessive secondary effects like chainring tooth deformation are no
longer remarkable, something unknown in the classic era.

Rings cannot wear chain (even if they were not aluminum teeth under hard
steel rollers). The syndrome is noted clearly here:
http://draco.acs.uci.edu/rbfaq/FAQ/8d.2.html

It's the worn rivet/sleeve which makes the chain 'out of pitch' and
hence wears the edge of the tooth. There isn't wear between roller and
tooth, the roller providing a pivot for the rivet inside it.
--
Andrew Muzi
<www.yellowjersey.org/>
Open every day since 1 April, 1971
** Posted from http://www.teranews.com **

peter

On Jun 3, 11:38 am, A Muzi <a...@yellowjersey.org> wrote:

> travis.ha...@gmail.com wrote:
> > The first of the criteria in this article is incorrect. I put a new
> > Sachs or SRAM chain on new chainrings of different manufacturers, and
> > they all fit under the chain differently, some allowing distinctly
> > different amounts of lift. I asked on this list how to know,
> > quantitatively, that a chainring was worn, and was told by such as
> > Andrew Muzi :It's worn out if the chain skips.
>
> > Unanswered was a second question: Does a worn chainring wear out
> > chains prematurely. Expensive as 10 speed chains are, and plentiful as
> > chainrings are, this could cause you to care more about worn rings.
>
> I wasn't being flippant; chainring wear is not usually obvious otherwise.
>
> Jobst refers to classic road rings, relatively clean, hard, of good
> quality and in sizes over 42t.

That describes my chainrings (except for the 'clean'), but I still had
problems on my 52-tooth ring with skipping due to wear a couple years
ago. Turned the ring over so the pressure contact with the chain is
on the opposite side of the teeth and it's been doing fine so far.
But I'm sure it'll eventually wear out again and start skipping.

> Rings cannot wear chain (even if they were not aluminum teeth under hard
> steel rollers). The syndrome is noted clearly here:http://draco.acs.uci.edu/rbfaq/FAQ/8d.2.html

Agreed.

jobst.brandt@stanfordalumni.org

Peter Rathman wrote:

>>> The first of the criteria in this article is incorrect. I put a
>>> new Sachs or SRAM chain on new chainrings of different
>>> manufacturers, and they all fit under the chain differently, some
>>> allowing distinctly different amounts of lift. I asked on this
>>> list how to know, quantitatively, that a chainring was worn, and
>>> was told by such as Andrew Muzi: It's worn out if the chain skips.

>>> Unanswered was a second question: Does a worn chainring wear out
>>> chains prematurely. Expensive as 10 speed chains are, and
>>> plentiful as chainrings are, this could cause you to care more
>>> about worn rings.

>> I wasn't being flippant; chainring wear is not usually obvious
>> otherwise.

>> Jobst refers to classic road rings, relatively clean, hard, of good
>> quality and in sizes over 42t.

> That describes my chainrings (except for the 'clean'), but I still
> had problems on my 52-tooth ring with skipping due to wear a couple
> years ago. Turned the ring over so the pressure contact with the
> chain is on the opposite side of the teeth and it's been doing fine
> so far. But I'm sure it'll eventually wear out again and start
> skipping.

>> Rings cannot wear chain (even if they were not aluminum teeth under
>> hard steel rollers). The syndrome is noted clearly here:

http://draco.acs.uci.edu/rbfaq/FAQ/8d.2.html

> Agreed.

I have posted pictures of a chainring that has its teeth nearly gone
from wear but still worked well on the steepest hills (Sonora Pass).

http://home.comcast.net/~carlfogel/download/zzz_006.jpg

When thinking about chains, this article is appropriate:

http://pardo.net/bike/pic/fail-004/000.html

Jobst Brandt

jobst.brandt@stanfordalumni.org

Just in case you need some special ones, here's a page of great CW's:

http://www.bikecult.com/works/chainwheel.html

Jobst Brandt

A Muzi

> Peter Rathman wrote:
>>>> The first of the criteria in this article is incorrect. I put a
>>>> new Sachs or SRAM chain on new chainrings of different
>>>> manufacturers, and they all fit under the chain differently, some
>>>> allowing distinctly different amounts of lift. I asked on this
>>>> list how to know, quantitatively, that a chainring was worn, and
>>>> was told by such as Andrew Muzi: It's worn out if the chain skips.

>>>> Unanswered was a second question: Does a worn chainring wear out
>>>> chains prematurely. Expensive as 10 speed chains are, and
>>>> plentiful as chainrings are, this could cause you to care more
>>>> about worn rings.

>>> I wasn't being flippant; chainring wear is not usually obvious
>>> otherwise.

>>> Jobst refers to classic road rings, relatively clean, hard, of good
>>> quality and in sizes over 42t.

>> That describes my chainrings (except for the 'clean'), but I still
>> had problems on my 52-tooth ring with skipping due to wear a couple
>> years ago. Turned the ring over so the pressure contact with the
>> chain is on the opposite side of the teeth and it's been doing fine
>> so far. But I'm sure it'll eventually wear out again and start
>> skipping.

>>> Rings cannot wear chain (even if they were not aluminum teeth under
>>> hard steel rollers). The syndrome is noted clearly here:

> http://draco.acs.uci.edu/rbfaq/FAQ/8d.2.html

>> Agreed.

jobst.brandt@stanfordalumni.org wrote:
> I have posted pictures of a chainring that has its teeth nearly gone
> from wear but still worked well on the steepest hills (Sonora Pass).
> http://home.comcast.net/~carlfogel/download/zzz_006.jpg
> When thinking about chains, this article is appropriate:
> http://pardo.net/bike/pic/fail-004/000.html

You call those TA chainring teeth 'nearly gone'? Look at any cheap urban
MTB with its typical 'orange chain'. Their middle rings often show a
tooth height of only 3~4mm!
--
Andrew Muzi
<www.yellowjersey.org/>
Open every day since 1 April, 1971
** Posted from http://www.teranews.com **